M30 Ride-On Sweeper-Scrubber | Tennant Company.Tennant M30 Parts

Looking for:

- Tennant M30 Parts —  

Click here to DOWNLOAD

     

TENNANT PARTS MANUALS - ORDER ONLINE - FAST SHIPPING - LOW PRICES.

 

Hide thumbs Also See for M30 : Operator's manual pages , Service manual pages , Instruction bulletin 12 pages. Table Of Contents. Quick Links. See also: Service Manual , Operator's Manual. Table of Contents. The Safe Scrubbing Alternative. Hygenic Fully Cleanable Tanks. Integrated Cleaning System.

ES Extended Scrub System. Lower Total Cost of Ownership. Previous Page. Next Page. Scrubber Tennant M20 Instruction Bulletin 12 pages. Scrubber Tennant M20 Instruction Bulletin 4 pages. Scrubber Tennant M17 Instruction Bulletin 9 pages. Scrubber Tennant Service Manual Tennant automatic scrubbers service manual pages. Specifications and parts are subject to change without notice. Page 3: Table Of Contents M30 6- Page Apply operation immediately.

M30 6- Page 8 Keep area well ventilated. The optional equipment may not be specified in these charts. Some machines may not be equipped with all components shown. Ignition switch S 7. Horn Switch S 8. Audible Alarm 9. Solution decrease button - - Brush pressure decrease button - - Filter shaker button Sweep vacuum fan button Side brush button option Engine speed button Supervisor control buttons M30 6- Page 15 5. Pressure Washer Hydraulic Valve 6.

LPG Fuel Tank Spray Nozzle Hose 7. Hydraulic Oil Temperature Sensor S FaST System Components 8. Fuel Tank Sweeping Vacuum Fan Motor Scrubbing Vacuum Fan Motor Steering Cylinder Main Hydraulic Valve Manifold Side Brush Motor Side Brush Motor 9.

ES Pump Solution Tank Full Switch S 4. Left Side Squeegee Lift Cylinder 5. Main Brush Motor Rear Solution Tank 6. Right Side Squeegee Lift Cylinder Propel Motor 2.

Sweeping Vacuum Fan Motor 3. Scrubbing Vacuum Fan Motor 4. Hydraulic Oil Reservoir 6. Scrub Head Lift Cylinder 7. The engine oil capacity is 6 L 6. M30 6- Page Hydraulics Tennant hydraulic fluid is specially selected to meet reservoir or operate the machine with a low level the needs of Tennant machines.

There are two fluids available for different temperature ranges: of hydraulic fluid in the reservoir. Damage to the machine hydraulic system may result. Page Hydraulic Hoses Serious infection or reaction can occur if proper medical treatment is not given immediately. Keep area well ventilated. This fuel system however is self-priming. The return line comes from the top of the injector that allows the air to escape through the return line.

M30 6- Page Battery Refer to the diagram below for locations of the fuses and relays on the relay panel. The M10 relay for the optional spray nozzle is located behind the battery. The Thermo--Sentry automatically resets after cooling down. M30 6- Page 35 5. Pull the brushes out from the scrub head. Reinstall the brush idler plates. Close the inner and outer brush doors.

Check and adjust the brush pattern if needed. Observe the brush patterns. If the brush pattern is the same width across the entire length of each brush and both brushes are the same width, no adjustment is necessary.

Tighten the mounting bolts. Recheck the pattern. Readjust if necessary. M30 6- Page Side Brush Option 4. Remove the side brush from underneath the side brush assembly.

Place the new side brush underneath the side brush assembly and lift the side brush up onto the side brush hub until the brush locks onto the hub.

M30 6- Page Fast System 5. Scrub with the FaST system for a few minutes to allow the detergent to reach maximum foaming. M30 6- Page Squeegee Blades 7.

Remove the rear squeegee. Remove both mounting knobs from the rear squeegee assembly. Turn on the machine, raise the scrub head, and turn off the machine. Remove the rear squeegee assembly from the machine. M30 6- Page 41 Install the new front squeegee blade or rotate the existing blade to the new edge.

Be sure the holes in the squeegee blade are hooked onto the tabs. Tighten the rear retaining band tension latch. Check and adjust the rear squeegee if necessary. Remove the retaining band from the side squeegee assembly. Pull the pin from the squeegee bumper and open the squeegee bumper. Reattach the side squeegee retaining band to the side squeegee assembly.

Drive the machine forward with the squeegee down to recheck the squeegee blade deflection if adjustments were made. Readjust the squeegee blade deflection if necessary. Readjust the squeegee blade deflection if 12 mm necessary.

To winch the machine onto the truck or trailer, attach the winching chains to the holes in the rear jacking brackets behind the rear tires.